Материал: Russian Journal of Building Construction and Architecture

Note: *the numerator is compaction using vacuum—type rollers; the denominator is compaction using static rollers; Ку is the coefficient of compaction; W is water saturation.

As the parameter q/R increases, so does the density and water saturation goes down for the compaction options compared. However for compaction accompanied by vacuumization higher compaction and lower water saturation coefficients are attained.

Significant changes occur as the parameter q/R goes up from 0.02 МPа to 0.03 МPа. A further increase in the parameter does not cause any changes in the assessment criteria. In Fig. 4а at n = 4 boundaries are shifted towards larger values of q/R.

Conclusions

1.The analysis of the obtained results shows that rational value of the parameter q/R during compaction accompanied by vacuumization at the temperature of 125…120 °С and initial coefficient of compaction of 0.91 is 0.03…0.035 МPа for the number of runs n = 8.

2.Inconsistencies of the results of industrial and laboratory tests are not higher than 10 %, which we find quite satisfying.

3.The results of the research allow rational contact pressures under the mills of the roller to be identified as well as design technological parameters of chosen mills depending on the type of an optimal mode of operation including the speed, vibration parameters and number of runs to make sure the compaction of asphalt concrete mixes and a high-quality is the most efficient.

References

1. Badalov V. V. Issledovanie katkov pri uplotnenii asfal'tobetonnykh dorozhnykh pokrytiy. Avtoref. diss. kand. tekhn. nauk [Research rollers during compaction of asphalt pavements. The abstract of thesis of cand. of eng. sci.]. Leningrad, 1974. 17 p.

51

Russian journal of building construction and architecture

2.Zubkov A. F., Kharkhuta N. Ya. [Comparison of parameters of vibratory and static rollers for compaction of asphalt mixes]. Trudy SoyuzdorNII «Issledovanie sovremennykh sposobov i sredstv uplotneniya gruntov i konstruktivnykh sloev dorozhnykh odezhd» [Proc. of Soyuzdornii «Research of modern methods and means of compaction and structural layers of road pavements»], 1975, iss. 84, pp. 124—132.

3.Zubkov A. F. Issledovanie parametrov vibratsionnykh katkov pri uplotnenii asfal'tobe-tonnykh pokrytiy. Avtoref. diss. kand. tekhn. nauk [Study of parameters of vibrating rollers for compacting asphalt concrete pavement. The abstract of thesis of cand. of eng. sci.]. Leningrad, 1974. 16 p.

4.Ivanchenko S. N., Nosov S. V. Issledovanie vliyaniya vakuumirovaniya na strukturu dorozhno-stroitel'nykh materialov pri ikh uplotnenii [Study of the effect of vacuum on the structure of road-building materials compaction]. Issledovanie rabochikh protsessov i dinamiki vibratsionnykh mashin s reguliruemymi parametrami [Study work processes and the dynamics of vibrating machines with adjustable settings]. Yaroslavl, YaPI, 1984, pp. 21—23.

5.Ivanchenko S. N., Shestopalov A. A. Napryazhenno-deformirovannoe sostoyanie materiala pri uplotnenii kat-kom s vakuumnym ustroystvom [The stress-strain state of the material when compacted by rolling with a vacuum device]. Issledovanie i ispytanie stroitel'nykh mashin i oborudovaniya [Research and test of construction machines and equipment]. Khabarovsk, Izd-vo Khabarovsk. gos. tekhn. un-ta, 1993, pp. 58—64.

6.Kovalenko Yu. Ya. Issledovanie samokhodnykh vibratsionnykh katkov dlya uplotneniya asfal'-tobetonnykh smesey. Avtoref. diss. kand. tekhn. nauk [The study of the self-propelled vibrating rollers for compaction of asphalt mixes. The abstract of thesis of cand. of eng. sci.]. Leningrad, 1979. 23 p.

7.Lozhechko V. P. Issledovanie rabochego protsessa gladkoval'tsovogo katka s vakuumnym ballastnym ustroystvom. Avtoref. diss. kand. tekhn. nauk [The study workflow Sladkovicovo rink with a vacuum ballast device. The abstract of thesis of cand. of eng. sci.]. Leningrad, 1981. 19 p.

8.Nosov S. V. Vliyanie tekhnologicheskikh parametrov dorozhnykh katkov na uplotnenie asfal'-tobetonnoy smesi [Influence of technological parameters of road rollers for compaction of asphalt mixture]. Stroitel'nye i dorozhnye mashiny, 2001, no. 7, pp. 5—7.

9.Nosov S. V. Vybor parametrov i rezhima raboty vibratsionnogo katka s vakuumnym ustroy-stvom dlya uplotneniya asfal'tobetonnykh dorozhnykh pokrytiy. Avtoref. diss. kand. tekhn. nauk [The choice of parameters and mode of operation of the compactor with the vacuum device for compaction of asphalt pavements. The abstract of thesis of cand. of eng. sci.]. Leningrad, 1989. 16 p.

10.Nosov S. V., Nosov V. V. Dinamicheskaya model' vibratsionnogo katka s vakuumnym ustroystvom [A dynamic modelof thecompactorwiththevacuumdevice].Izvestiya vuzov. Stroitel'stvo i arkhitektura,no.7,pp.101—107.

11.Nosov S. V., Nosov V. V. K voprosu po opredeleniyu modulya deformatsii uplotnyaemykh sloev dorozhno-stroitel'nykh materialov [To the question on the definition of the modulus of deformation of compacted layers of road construction materials]. Izvestiya vuzov. Stroitel'stvo, 1991, no. 10, pp. 104—108.

12.Nosov S. V. Opredelenie prochnostnykh kharakteristik vakuumirovannykh asfal'tobetonnykh smesey dlya ustroystva dorozhnykh pokrytiy [Determination of strength characteristics of vacuum asphalt mixtures for road coverings]. Optimal'nye vibratsionnye rabochie protsessy v stroitel'stve [Optimal vibration work processes in construction]. Yaroslavl, YaPI, 1989, pp. 33—38.

13.Nosov S. V. Osobennosti tekhnologii uplotneniya dorozhnykh pokrytiy katkami pri ispol'zovanii na nikh vakuumnykh ustroystv [Technology features a seal pavement rollers if you use them vacuum devices].

Stroitel'nye i dorozhnye mashiny, 1999, no. 9, pp. 6—9.

52

14.Nosov S. V. Razrabotka tekhnologiy uplotneniya dorozhnykh asfal'tobetonnykh smesey i grun-tov na osnove razvitiya ikh reologii. Avtoref. diss. doct. tekhn. nauk [Development of technologies for the compaction of road asphalt mixes and soils on the basis of their rheology. The abstract of thesis of dr. of eng. sci]. Voronezh, 2013. 34 p.

15.Nosov S. V. Tekhnologicheskie rezhimy raboty uplotnyayushchikh mashin i zakonomernosti up-lotneniya dorozhno-stroitel'nykh materialov na osnove razvitiya ikh reologii [The technological regimes of compacting machines and regularities of compaction of road construction materials on the basis of their rheology]. Nauchnyy vestnik Voronezhskogo GASU. Stroitel'stvo i arkhitektura, 2011, no. 3 (23), pp. 87—98.

16.Nosov S. V. Tekhnologiya uplotneniya goryachikh asfal'tobetonnykh smesey s primeneniem vib-ratsionnykh katkov s vakuumnym ustroystvom [Seal technology of hot asphalt concrete mixtures using vibrating rollers with a vacuum device]. Nauchnyy vestnik Voronezhskogo GASU. Stroitel'stvo i arkhitektura, 2012, no. 4 (24), pp. 53—63.

17.Nosov S. V. Uplotnenie asfal'tobetonnykh smesey s vakuumirovaniem [The compaction of asphalt mixtures with vacuum]. Nauka i tekhnika v dorozhnoy otrasli, 2010, no. 3, pp. 36—39.

18.Podol'skiy Vl. P., Ryabova O. V., Nosov S. V. Razvitie reologii dorozhno-stroitel'nykh materialov na puti sovershenstvovaniya tekhnologiy ikh uplotneniya [Development of rheology of road-building materials in enhancing technology seals]. Nauchnyy vestnik Voronezhskogo GASU. Stroitel'stvo i arkhitektura, 2011, no. 3 (23), pp. 99—108.

19.Kharkhuta N. Ya., Shestopalov A. A. Vybor tipa i rezhima raboty katkov pri uplotnenii as-fal'tobetonnykh smesey [Select the type and mode of operation of rollers in the compaction of asphalt mixtures]. Avtomobil'nye dorogi, 1983, no. 3, pp. 24—25.

20.Shestopalov A. A., Ivanchenko S. N., Nosov S. V. Vliyanie parametrov katkov i temperatury na uplotnyaemost' asfal'tobetonnykh smesey ukatkoy s vakuumirovaniem [Influence of parameters of rollers and temperature on the compactibility of asphalt mixes compacted with vacuum]. Rabochie protsessy i dinamika mashin i mekhanizmov dlya razrabotki, uplotneniya gruntov i vibratsionnogo formovaniya izdeliy [Workflows and dynamics of machines and mechanisms for the development, compaction and vibration moulding products]. Yaroslavl, YaPI, 1986. pp. 57—61.

53

Russian journal of building construction and architecture

BUILDING MECHANICS

UDC624.04+624.6

V. S. Safronov1, V. V. Zazvonov2

PROBABLE METHOD OF CALCULATING THE EFFECTS

OF TEMPORARY STATIC-LOADS ON SOIL BRIDGE CONSTRUCTION

Voronezh State University of Architecture and Civil Engineering Russia, Voronezh, tel.: (473)271-52-30, e-mai: vss22@mail.ru 1D. Sc. in Engineering, Prof. of the Dept. of Structural Mechanics Ltd «PPP «Absida»

Russia, Moscow, tel.: +7-910-409-65-73, e-mail: vladimirzazvonov@yandex.ru 2PhD in Engineering, Head engineer

Statement of the problem. The effect of the variation of modulus of the deformation of the sand backfill on the stress-strain state of reinforced concrete vaulted shells under the effects of the temporary static-loads is investigated.

Results. The method based on the statistical tests of the method of probable calculations of the distri-bution of the forces in the vaulted concrete shell of the filled in with soil bridge constructions from the temporary static-loads is proposed. A spatial finite element calculation schema where a stochastic model of the surrounding body of soil appears to be a random field with given statistical characteristics is applied. The results of numerical studies that are based on the exploited for transportation construc-tion are presented.

Conclusions. A minor influence of a scatter of the modulus of deformation on the distribution of normal and bending moments is identified, which allows one to be limited to a deterministic setting the modulus of elasticity of soil backfill while performing strength calculations of reinforced concrete vaulted shells in the elastic medium.

Keywords: soil bridge, thin-walled ferroconcrete arch, probable calculation, sand filling, stress-strained state, bending moments, normal conditions.

Introduction

According to the guidelines (SNiP 2.05.03-84* (SP 35.13330.2011) “Bridges and Pipelines” for strength and deformation calculations of a bridge under construction mechanical characteristics of materials of bearing structures and sandy filling are considered determined.

© Safronov V. S., Zazvonov V. V., 2017

54

In fact even well-constructed surrounding arched bridge spans fluctuate considerably. Besides, a wide range of the parameters has acting loads as well as strength and deformation characteristics of the material of a ferroconcrete shell. Considering these fluctuations of the system “shell –– elastic environment” is essential as a sandy filling has not only an active pressure on the shell but also resists the deformations of the shell and has a significant effect on its stress-strain.

Therefore there should be no restrictions in stress-strain associated with a wide range of the parameters of the system. This article sets forth a method of investigating the stress-strain of bridges using sandy fillings in a probabilistic manner and looks at a range of the parameters of the stress-strain of a bearing structure considering fluctuations of deformation characteristics of a soil filling.

1. Original assumptions. The parameters determining the fluctuations of the stress-strain of a bearing shell in the elastic environment are grouped if the following are dominant for them:

1.Loading parameters impacting the shell;

2.Geometric and physical characteristics of the arch material;

3.Deformation characteristics of the environment surrounding a bearing shell.

The impact of the first two factors has been studied in detail [1—5]. The influence of the probabilistic character of deformation parameters of the environment on the stress-strain of a ferroconcrete shell has not been sufficiently investigated. It is done here with the use of the method of statistical tests. The massive surrounding the shell is modelled with a continuous stochastic environment with different volumetric finite elements in the form of parallelepipeds and tetrahedrons. Probabilistic character of deformation parameters should be taken into account using two different approaches: the accurate one based on the theory of random fields and the approximated one that uses a simplified stationary model with a constant mathematical anticipation m(x, y, z) = const and dispersion D(x, y, z) = const.

The accurate approach requires multi-dimensional distributions of deformation characteristics in the surrounding shell of a continuous soil environment: the deformation modulus Е, the Poisson coefficient v, adhesion с, angle of the internal friction φ, dilatancy. It is quite challenging to specify a random field using multi-dimensional distribution functions and leads to daunting mathematical and calculation problems. Describing random fields is possible only using the methods of random functions. For the normal law of distribution of the parameters along the environment statistical characteristics of the determining parameters S will suffice:

55